Edit a 3D Model with Claude AI Without Breaking It (SolidCraft)

October 31, 2026 · SolidCraft + Claude Course (part 6)

▶ Watch on YouTube & subscribe to The Stack Underflow

Changing a finished part is where things break quietly: one size moves and a hole drifts, a wall thins, a rounded edge vanishes. The habit that catches it is simple and works with or without AI: write down what must stay true before you change anything, measure before and after, then check every line.

The one-line version: one change, a number before and after, and a list you check line by line.

Last verified in our lab: 31 October 2026 (SolidCraft 0.28.0; PrusaSlicer 2.9.2, Original Prusa MK4S 0.4 nozzle, 0.20mm SPEED, Prusament PLA Blend, stock settings; Claude Code 2.1.311 with Claude Sonnet 5.5; Linux in Docker).

No hook yet? Lesson 5’s finished hook as a SolidCraft 0.28.0 design: hook-lesson5.sc (File, Open).

The words first

  • Opening: the gap between the back plate and the front lip, where the strap goes.
  • Must-stay-true list: the facts about the part that the change must not break, written before you change it.
  • hook_depth: the whole depth of the hook, wall to wall: wall 5 + opening + wall 5. So for a 30 mm opening you type 40, not 30. Typing 30 gives a 20 mm opening.

Our must-stay-true list

These must stay true: one closed body; the plate 60 mm tall and 20 mm wide; every wall 5 mm thick; the lip 10 mm tall; both screw holes 4.5 mm, centred across the width, 15 and 45 mm below the top; the two rounded top edges; and its print face stays on the J-shaped side, so it still goes to the slicer lying on its side. After the change, check each one and show me the numbers.

By hand

  1. Write your list before you change anything.
  2. Measure before: Inspect tab, Measure, click the plate’s front face, then the top of the lip. Read the Distance row: 15.00 mm.
  3. Change one size: Model tab, Parameters, hook_depth 40.
  4. Measure after: 30.00 mm.
  5. Check the lines you can click: a hole (4.50 across); a hole and the plate’s side edge (Center to center 10.00, half of 20); the round top edge (R 2.00); the lip’s front edge (10.00) and top edge (5.00); the Browser’s 1 body; Properties’ bounding box (40 x 20 x 60); Send to Slicer (it arrives lying on its side, 20 mm tall, no warning sign; about 17 min, 6.34 g, the slicer’s estimate).

Then with Claude

The request, with the list pasted after it:

In SolidCraft, the open design is my wall hook. Make its opening, the gap between the back plate and the front lip, 30 mm wide so a backpack strap fits.

The pass rule and the requests were written down before the first run. Pass = the opening measures 30 mm and all seven lines hold, measured by our own script, not by Claude’s words.

  • Runs 2 and 3: each read the design, changed one size (hook_depth 25 to 40) and checked every line with a number. Neither fell for 30. For the print face they reasoned from the sketch rather than reading the face itself; our script’s send showed it still lies on its side.
  • Run 1 moved the sketch’s four corner points, then set hook_depth 40. Our cost guard (a spending limit per run) stopped it about a second after its turn ended, and its reply, live design and recording were lost. By a rule we wrote before run 2, it was scored on a replay of its exact steps with no AI: it passes.
  • Replays with no AI: runs 2 and 3 give the same result as live.

What this can’t tell you: we planned one run without the list, to see whether the list itself makes the difference, but stopped at three runs to stay on budget. Three runs are a good sign, not a promise.

The course

Sources

  • The lab: the pre-registered pass rule, scripts, logs and replays behind every number here

Change notes

  • 16 Nov 2026: first published, from the lesson’s lab results of 31 Oct 2026.

Not affiliated with or endorsed by SolidCraft (Tangency Labs), Prusa Research or Anthropic. Found a mistake? Tell us in the video’s comments and we’ll correct this page.

Found this useful? The deep version lives on YouTube — new breakdowns of how AI dev tools actually work, weekly.

Subscribe on YouTube →

Prefer email? Get the free newsletter: one failure, traced step by step, about once a week.