SolidCraft to 3D Printer: Export STL/3MF and Check It in the Slicer
▶ Watch on YouTube & subscribe to The Stack Underflow
A 3D printer doesn’t read your design. A slicer does: it cuts the part into thin layers and writes the printer’s instructions. Before that, four things must be true: the part is one body, it has the right size, it is closed (no gaps in its surface), and it lies on a sensible face. The face it lies on changes the print time and whether the slicer warns you.
The one-line version: check one body, the size and closed, then pick the print face before you send it to the slicer.
Last verified in our lab: 31 October 2026 (SolidCraft 0.28.0; PrusaSlicer 2.9.2, stock MK4S, 0.20mm SPEED, PLA; Claude Code 2.1.311 with Claude Sonnet 5.5; Linux in Docker). Lesson 4 used 0.27.1: update first. 0.28.0 added the print face, and 0.28 designs don’t open in 0.27. The slicer numbers are its estimates: we didn’t print the hook.
The words first
- STL: triangles only, with no unit. Slicers read its numbers as millimetres.
- 3MF: also stores the unit (SolidCraft writes millimetres).
- Print face: the face the part should lie on in the slicer. Only the copy sent to the slicer turns; your design stays as drawn.
- Layer: one slice of the print. At 0.2 mm, a part 60 mm tall is 300 layers; 20 mm tall is 100 layers.
No hook yet? Lesson 4’s finished hook as a SolidCraft 0.28.0 design: hook-lesson4.sc.
By hand
- Install PrusaSlicer (free, prusa3d.com). On first start, pick any printer (you can slice without one). SolidCraft then lists it in Send to Slicer.
- Check 1, one body: the Browser on the left says 1 body.
- Check 2, the size: right-click Body1, Properties: bounding box 25.00 x 20.00 x 60.00 mm.
- Right-click Body1, Send to Slicer, leave Print face at Select, slicer PrusaSlicer, Send. In PrusaSlicer the size boxes say 25, 20, 60 mm.
- Check 3, closed: no warning sign next to the part’s name in PrusaSlicer. (A copy we broke on purpose shows an orange triangle: “7 open edges”.)
- Slice now: standing, 33 min, 5.37 g, and “Detected print stability issues: Low bed adhesion. Consider enabling supports. Also consider enabling brim.”
- Check 4, the face it lies on: close the slicer, Send to Slicer again, click the Print face box, turn the view to the hook’s side (the green Y ball, top right), click the J-shaped face, Send. Slice now: 15 min, 5.37 g, no warning.
- A file instead: right-click Body1, Save As Mesh, STL or 3MF, Save. Note: Save As Mesh writes the hook standing, as drawn, even with a print face picked. In PrusaSlicer press F (Place on face) and click the J side, or use Send to Slicer.
What the numbers say
- Same plastic either way: 5.37 g. Standing is 300 layers; on its side, 100.
- On its back: 20 min and a different warning (floating bridge anchors).
- With supports switched on: 0 g of support in every orientation, and the warning goes away, because the slicer runs that check only with supports off. Laying it on its side clears it without changing a setting, and halves the time.
Then with Claude
One run per request. The “asked” run added:
Before you send it, check that it's ready to print: one body, closed, the size in millimetres, and pick the flat face it should lie on.
- Not asked: read the design and sent the hook as drawn, standing: 33 min and the warning. It said it hadn’t checked the orientation.
- Asked: set the print face on the hook’s side and sent it: 15 min, no warning, the same file as ours byte for byte. (Its claim that it’s “stronger lying flat” was not tested.)
- Our test with no AI: our script replayed each run’s tool calls in a fresh SolidCraft and got the same file both times.
- SolidCraft’s docs say it asks before an AI agent sends a file to a slicer; no such prompt appeared in our two runs.
The course
- Previous: Lesson 4: holes and fillets
- Next: Lesson 6: edit a model with Claude without breaking it
- The lab for this lesson: solidcraft-course-lab/out/l5
Sources
- PrusaSlicer 2.9.2 with its stock Original Prusa MK4S profile: every time, weight and warning above
- The lab: scripts, logs, replays and the slicer outputs
Change notes
- 16 Nov 2026: first published, from the lesson’s lab results of 31 Oct 2026.
Not affiliated with or endorsed by SolidCraft (Tangency Labs), Prusa Research or Anthropic. Found a mistake? Tell us in the video’s comments and we’ll correct this page.
Found this useful? The deep version lives on YouTube — new breakdowns of how AI dev tools actually work, weekly.
Subscribe on YouTube →Prefer email? Get the free newsletter: one failure, traced step by step, about once a week.