SolidCraft Tutorial for Beginners: Sketch a 3D Part by Hand vs Claude

October 28, 2026 · SolidCraft + Claude Course (part 2)

▶ Watch on YouTube & subscribe to The Stack Underflow

Most 3D parts start as a flat drawing. You draw the outline on a plane, then push it out to give it thickness. This lesson makes a wall hook that way, first by hand, then by asking Claude, and measures both.

The one-line version: sketch the outline, extrude it, then check the volume and the bounding box in Properties. After a Claude build, also check which way up it is.

Last verified in our lab: 27-28 October 2026 (SolidCraft 0.25.0; Claude Code 2.1.311 with Claude Sonnet 5.5; Linux in Docker). Lesson 1 used 0.24.1, so update first: designs saved in 0.25.0 don’t open in 0.24.1.

The words first

  • Sketch: a flat drawing on a plane, like a drawing on paper.
  • Plane: the flat surface you draw on. XZ is the front plane: it stands up facing you.
  • Extrude: push the sketch straight out of the paper to make a solid.
  • Fully constrained: every line’s length and direction is pinned, so nothing can move by accident.
  • Bounding box: the smallest box the part fits in; its three sizes are the part’s overall size.

The part

A wall hook seen from the side, a flipped J. Back plate 60 mm tall, arm 25 mm deep, lip 10 mm high, all 5 mm thick, pushed out 20 mm.

Work out the answer before you build. The flat area of the J is 5 x 60 + 20 x 5 + 5 x 5 = 425 mm². Times 20 mm of depth: 8,500 mm³. The bounding box should be 25 x 20 x 60 mm.

By hand

  1. On the start page, click New design (millimetres). Still in lesson 1’s design? The house next to File brings you back to the start page.
  2. Model tab, New Sketch. The panel on the right asks for a plane: in the Browser, open Origin and click XZ.
  3. Drag down with the middle mouse button to make room above the origin. Click Line, then click the origin.
  4. Point the way each line goes, wait for the small H (level) or V (upright), type the length and press Enter: right 25, up 10, left 5, down 5, left 15, up 55, left 5. Then click the first point to close it (eight lines, seven typed). Press Esc. The panel says fully constrained.
  5. Finish Sketch, then Extrude. The J is already picked: replace the 10 with 20, click OK.
  6. The house on the bar at the bottom of the view shows it in 3D. Right-drag turns it, the wheel zooms.

Check it yourself

Right-click Body1 in the Browser, Properties. Look for Volume 8500.00 mm³ and a bounding box of 25 x 20 x 60 mm. Our hand-made hook stood on the floor (Z from 0 to 60). The History bar showed two steps: Sketch1, then Extrude1.

Then with Claude

With SolidCraft open and lesson 1’s plug connected, we typed:

In SolidCraft, sketch this outline on the XZ plane, starting at 0,0: right 25, up 10, left 5, down 5, left 15, up 55, left 5, then back to the start. Extrude it 20 mm.

Then: “Measure it, and list the steps in its timeline.”

What happened, in two runs with the same result:

  • One batch of four commands: create a sketch on XZ, the eight corners as one closed line, finish, extrude 20.
  • Measured: 8,500.0 mm³, 25 x 20 x 60, and the same two steps in the timeline.
  • But upside down: Z ran from -60 to 0. The XZ plane picked in the Browser keeps Z up; a sketch created on XZ through the plug points the sketch’s “up” toward -Z. Claude’s own reply said so and offered to flip it (we didn’t test the flip). Whether that’s meant or a bug, we can’t tell from our lab.
  • Its sketch has no dimensions: 14 degrees of freedom, so its lines are not pinned.

Why the numbers couldn’t catch it: the volume and the box sizes are the same either way up. So after every Claude build, look at the picture, or read the height: the bounding box or Z in Measure.

Our proof with no AI: Claude’s logged tool calls, replayed in a fresh SolidCraft, gave 8,500.0 mm³ and upside down again. Our STL checker: closed, 8,500.0 mm³.

Claude Code 2.1.311 started in auto mode, so no approval was asked. A Claude app can ask you first.

How this was filmed

The real SolidCraft window in a Linux container, recorded and zoomed onto the area being clicked. The by-hand clicks were played by a script at a person’s pace, so you see exactly the clicks a person makes. Claude Code ran in its own terminal; nobody touched the mouse during its run. Sped-up parts are marked.

The course

Sources

  • The lab: scripts, logs, tool-call records and the STL checker behind every number here

Change notes

  • 16 Nov 2026: first published, from the lesson’s lab results of 27-28 Oct 2026.

Not affiliated with or endorsed by SolidCraft (Tangency Labs) or Anthropic. Found a mistake? Tell us in the video’s comments and we’ll correct this page.

Found this useful? The deep version lives on YouTube — new breakdowns of how AI dev tools actually work, weekly.

Subscribe on YouTube →

Prefer email? Get the free newsletter: one failure, traced step by step, about once a week.